www.canstar.com.au

Introduction: Building a Flat Roof A flat roof, while seemingly simple, requires careful planning and execution to ensure proper drainage and longevity. This guide provides a step-by-step approach to constructing a durable flat roof. Remember to consult local building codes and consider hiring a professional if you lack experience.

Step 1: Planning and Preparation

Determine Roof Load: Calculate the load the roof needs to bear, including snow load in colder climates.

Obtain Permits: Check local regulations and obtain necessary building permits.

Gather Materials and Tools: You'll need lumber (joists, sheathing), roofing material (modified bitumen, EPDM, TPO), insulation, flashing, fasteners, safety equipment (harness, goggles), measuring tools, saws, drills, hammers, and a roofing torch (if using modified bitumen).

Design for Drainage: Plan for a slight slope (minimum 1/4 inch per foot) towards a drain or scuppers. This is crucial for preventing water pooling.

Step 2: Framing the Roof

Install Joists: Space joists according to load requirements and lumber size. Ensure proper alignment and secure them to the supporting walls with appropriate fasteners.

Create the Slope: Achieve the required slope using tapered insulation or by shimming the joists. Consistent slope is paramount.

Add Blocking: Install blocking between joists for added stability and to prevent twisting.

Step 3: Sheathing the Roof Deck

Lay the Sheathing: Use OSB or plywood sheathing, ensuring it's rated for exterior use. Stagger the seams for strength.

Fasten the Sheathing: Securely fasten the sheathing to the joists with screws or nails according to manufacturer's recommendations.

Seal the Seams: Tape the seams of the sheathing with seam tape to prevent moisture infiltration.

Step 4: Installing Insulation

Choose Insulation: Select the appropriate insulation type and R-value based on climate and energy efficiency goals. Options include rigid foam board, spray foam, or batt insulation.

Install Insulation: Place insulation tightly between joists or over the sheathing, depending on the chosen method. Secure it properly.

Step 5: Installing the Roofing Membrane This step depends heavily on the chosen roofing material. We'll outline the basic principles, but always refer to the manufacturer's instructions.

Modified Bitumen: Overlap and torch-apply the roofing membrane, ensuring a watertight seal at seams and edges. Use proper safety precautions when using a torch.

EPDM: Adhere the EPDM membrane to the substrate with adhesive, carefully rolling out wrinkles and ensuring a tight bond.

TPO: Similar to EPDM, TPO membranes are adhered or mechanically attached to the roof deck.

Step 6: Installing Flashing

Flash Around Penetrations: Install flashing around vents, chimneys, skylights, and any other roof penetrations. This is essential to prevent leaks.

Flash at Edges: Install edge flashing along the perimeter of the roof, ensuring it overlaps the roofing membrane and extends down the wall.

Step 7: Drainage and Finishing

Install Drains/Scuppers: Ensure drains or scuppers are properly installed and connected to a downspout system to effectively remove water.

Inspect and Seal: Thoroughly inspect the entire roof for any gaps or imperfections and seal them with appropriate sealant.

Consider a Protective Coating: Applying a reflective or protective coating can extend the life of the roof and improve energy efficiency.

Conclusion: A Properly Built Flat Roof Constructing a flat roof is a challenging project, but by following these steps and taking precautions, you can create a durable and functional roof. Regular inspection and maintenance are crucial for extending its lifespan. If you are unsure about any part of the process, consult a qualified roofing professional.

Buying Or Building Your Dream House: The Pros & Cons

www.canstar.com.au

Become A Home Builder And Build Your Own Home By Yourself

www.workinghomeguide.com

How To Build A House

www.realestate.com.au

Read More..

countrylumber.us

Introduction: Building Your Own Shiplap Shed

Ready to add some stylish and functional storage to your backyard? Building a shed with shiplap siding is a fantastic DIY project that offers both beauty and durability. This step-by-step guide will walk you through the process, from planning to completion. Get ready to roll up your sleeves and create a stunning addition to your property!

Step 1: Planning and Preparation

First, determine the size and location of your shed. Check local building codes and HOA regulations for any permit requirements or restrictions. Create a detailed plan, including dimensions, materials list, and a clear visual representation of the shed. Once your plans are set, gather all the necessary tools and materials.

Step 2: Foundation Construction

Start by preparing the ground for the foundation. Remove any vegetation and level the area. Options for the foundation include a concrete slab, gravel pad, or pressure-treated wood frame. For a wood frame foundation:

• Cutting the Frame: Cut the lumber according to your shed dimensions.
• Assembling the Frame: Assemble the frame using screws and brackets. Ensure the frame is square and level.
• Laying the Foundation: Place the frame on the prepared ground and ensure it is level.

Step 3: Framing the Walls

Now, it's time to build the wall frames.

• Cutting Studs: Cut the vertical studs and top and bottom plates according to your plan.
• Assembling the Walls: Assemble the wall frames by attaching the studs to the top and bottom plates using screws or nails. Ensure proper spacing between studs (typically 16 or 24 inches on center).
• Raising the Walls: Raise the walls and attach them to the foundation frame using screws or nails. Ensure the walls are plumb and braced for stability.

Step 4: Installing the Roof

The roof provides protection from the elements.

• Building Rafters: Build or purchase roof rafters based on your shed's dimensions and desired roof pitch.
• Attaching Rafters: Attach the rafters to the top plates of the walls, ensuring proper spacing and alignment.
• Adding Sheathing: Cover the rafters with plywood or OSB sheathing and secure it with nails or screws.

Step 5: Installing Shiplap Siding

Here comes the beautiful shiplap siding.

• Preparing the Shiplap: Prime and paint or stain the shiplap boards before installation. This will protect the wood and give it a finished look.
• Installing the First Row: Starting at the bottom of the wall, install the first row of shiplap, ensuring it is level and aligned with the foundation.
• Overlapping Rows: Overlap each subsequent row of shiplap, using the rabbeted edges for a tight fit. Secure the boards with nails or screws.
• Cutting for Openings: Cut the shiplap boards to fit around windows and doors as needed.

Step 6: Installing Doors and Windows

Add doors and windows for access and light.

• Framing Openings: Ensure the door and window openings are properly framed.
• Installing Doors: Install the door frame and door, ensuring it is plumb and swings freely.
• Installing Windows: Install the window frame and window, ensuring it is sealed properly.

Step 7: Finishing Touches

Complete the shed with finishing details.

• Adding Trim: Add trim around doors, windows, and corners for a finished look.
• Caulking: Caulk any gaps or seams to prevent water intrusion.
• Painting or Staining: Apply a final coat of paint or stain to protect the wood and enhance its appearance.
• Adding Gutters (Optional): Install gutters to divert rainwater away from the shed.

Conclusion: Enjoy Your New Shiplap Shed

Congratulations! You've successfully built your own shiplap shed. This stylish and functional addition to your property will provide valuable storage space and enhance the overall aesthetic of your backyard. Enjoy the fruits of your labor!

Shiplap Siding

countrylumber.us

Pine Shiplap Siding Pricing Guide For Barn And Shed

www.wrrobinsonlumber.com

Pine Shiplap Siding Pricing Guide For Barn And Shed

www.wrrobinsonlumber.com

Read More..

diygardenplans.com

Introduction: Building Your Own Gambrel Shed

Gambrel sheds, with their barn-like roofs, offer excellent headroom and storage space. This guide provides a step-by-step approach to building your own DIY gambrel shed, from planning to completion. Safety is paramount; always wear appropriate safety gear like gloves, eye protection, and a dust mask when working with power tools and materials. Secure a building permit if required by your local regulations.

Step 1: Planning and Preparation

Design and Dimensions: Determine the shed's dimensions based on your needs and available space. Common sizes range from 8x10 to 12x16 feet. Consider the height of the walls and the roof pitch.

Create a Detailed Plan: Develop a comprehensive plan with precise measurements, including the foundation, framing, roofing, and door/window placements. Numerous free and paid plans are available online to guide you.

Material List: Compile a detailed list of all necessary materials, including lumber (pressure-treated for the base), plywood, roofing materials (shingles, metal), siding, nails, screws, hinges, door hardware, windows (if desired), and any insulation.

Tools: Gather the necessary tools, including a circular saw, miter saw, drill, impact driver, level, measuring tape, square, hammer, safety glasses, gloves, and a ladder. A nail gun can significantly speed up the framing process.

Site Preparation: Choose a level area for your shed. Clear vegetation and debris. Consider a gravel base for drainage or a concrete slab for a more permanent foundation.

Step 2: Building the Foundation

Gravel Base (Optional): If using a gravel base, excavate the area to a depth of several inches. Fill with compacted gravel to create a level surface.

Concrete Slab (Optional): Pour a concrete slab according to your plans. Ensure it is level and allow it to cure completely before proceeding.

Framing the Base: Construct a rectangular frame from pressure-treated lumber according to your dimensions. Use screws or nails to securely join the corners.

Leveling and Squaring: Ensure the base frame is perfectly level and square. Use shims if necessary to level the frame.

Anchoring: Secure the base frame to the ground or concrete slab using appropriate anchors.

Step 3: Framing the Walls

Cutting the Studs: Cut the studs to the desired length for your wall height.

Assembling the Walls: Lay out the top and bottom plates for each wall. Space the studs 16 inches on center (OC). Nail or screw the studs to the plates.

Adding Headers: Install headers above door and window openings to provide structural support.

Sheathing the Walls: Cover the framed walls with plywood sheathing. Use nails or screws to securely attach the sheathing to the framing.

Raising and Securing the Walls: Carefully raise the walls into place and secure them to the base frame. Use temporary bracing to keep the walls plumb.

Connecting the Walls: Connect the walls at the corners using nails or screws. Ensure the walls are properly aligned and plumb.

Step 4: Building the Gambrel Roof

Cutting the Rafters: This is the most complex part. Accurately measure and cut the rafters for both the upper and lower sections of the gambrel roof. Use a rafter table or online calculator to determine the correct angles and lengths.

Assembling the Roof Trusses: Assemble the roof trusses on the ground, ensuring they are square and structurally sound. Use gusset plates or plywood to reinforce the joints.

Raising the Trusses: Carefully raise the trusses into place and secure them to the top plates of the walls. Ensure the trusses are evenly spaced.

Adding the Ridge Board: Install a ridge board along the peak of the roof to provide additional support.

Sheathing the Roof: Cover the roof framing with plywood sheathing. Use nails or screws to securely attach the sheathing to the framing.

Step 5: Installing Siding and Roofing

Siding Installation: Install the siding of your choice (wood, vinyl, metal) to the exterior walls. Follow the manufacturer's instructions for proper installation.

Roofing Underlayment: Install roofing underlayment (felt paper or synthetic underlayment) to protect the roof sheathing from moisture.

Roofing Installation: Install the roofing material of your choice (shingles, metal roofing) according to the manufacturer's instructions. Overlap the roofing material properly to prevent leaks.

Step 6: Doors, Windows, and Finishing Touches

Door Installation: Install the door frame and hang the door. Ensure the door swings freely and latches securely.

Window Installation (if desired): Install the windows according to the manufacturer's instructions.

Trim and Finishing: Add trim around the doors, windows, and corners to give the shed a finished look.

Interior Finishing (Optional): Add insulation, drywall, or other interior finishing materials to create a more comfortable and functional space.

Painting or Staining: Paint or stain the exterior of the shed to protect it from the elements and enhance its appearance.

Conclusion: Enjoy Your New Gambrel Shed

Congratulations! You have successfully built your own gambrel shed. This provides additional storage space and enhances the value of your property. Regularly inspect your shed for any signs of damage or wear and make necessary repairs to ensure its longevity. Remember to keep the area around your shed clear of debris and overgrown vegetation to prevent moisture buildup and pest infestations.

10×12 Gambrel Storage Shed Plans

www.shedplansz.com

Gambrel

diygardenplans.com

Gambrel Shed Plans

howtospecialist.com

Read More..

Metal roofing company specialising in high quality new roofs | re-roofs | fascia, guttering and downpipes. office: woonona nsw | info@originalmetalroofing.com | m: 0422 989 219. My roof restoration are nutech paint approved roof professionals.. nutech paint are australia’s largest and oldest roof coating specialists who remain family and australian owned.. we exclusively use the nutech professional roof restoration system designed to withstand the tough australian environment and protect and enhance the appearance of your most valued asset.. My roof restoration pty ltd (t/a my roof restoration) australian proprietary company, limited by shares. registered address: 119 matthews avenue, orange, nsw, 2800 telephone number / mobile: 0412 634 399 email: spartridge8@bigpond.com.au. acn: 50 132 625 702 abn: 50 132 625 702 view record on asic website.

Portico, the scots church redevelopment | tonkin zulaikha

Harry seidler & associates: 9 castlereagh street enhancements

Pergolas, patios & decks | pioneer shade structures

Ge roofing provides fast and reliable roof installation and repair services for all types of buildings, from houses to apartment blocks, churches, schools, shops and more. specialising in a wide range of roofing services such as safety rail, new roof installation, re-roofing, roof maintenance, roof repairs, storm damage and guttering on your roof.. We are a small family owned & operated business with more than 30 years experience in roof tiling & roof restoration. we specialize in repairs to tiled roofs diagnosing the real cause of any problems. we also carry out repairs for insurance claims on your roof. we are fully licensed & insured. we are honest & reliable.. Mercer property is delighted to present to the market, this outstanding corner position, first-floor office space. this property features bright and spacious first-floor office space, coupled with outstanding roof-top garden space, perfect for client entertainment, or and outdoor workspace..

Read More..

May you like low pitch roof house plans. some times ago, we have collected galleries for your need, look at the picture, these are awesome galleries. we like them, maybe you were too. perhaps the following data that we have add as well you need. you must click the picture to see the large or full size photo. if you like and want to share you must click like/share button, maybe you can help. Plan 48-476 (above) features cool contemporary styling with simple roof planes. plan 430-99 is a beautiful mix of design and functionality, which provides the most efficient use of space possible in a 1,769 square foot home. craftsman-style plans may demand more details than others, but a few, judiciously located ones can go a long way.. The strengths of modern flat roof house plans. it will be a genuine idea to consider the modern flat roof house plans for various positive reasons. they focus on the importance of flat roof which is their selling theme. get along with the benefits of flat roof design. above all, the major benefit is being simple in construction process..

Sheds that are popular these days — modern sheds | toronto

Screened porch interior | interior of shed roof style

House plan #142-1048 : 3 bedroom, 1900 sq ft ranch

This set of free tiny house plans is a classic 8′ x 12′ house with a 12/12 pitched roof. the plans are 20 pages and are drawn to the same level of detail as my other tiny house plans. the walls are framed with 2x4s and the floor and roof are framed with 2x6s.. The roof design is not simply a finishing touch to cover the home, but a protective barrier from sun, wind, rain, run off, snow buildup and more. often, the roof can present a larger visible surface area than the walls, so adequate planning must be undertaken. drawing a suitable roof design will take a mastery of measurements and facts that. Although rarely the first thing you notice, a roof says much about a home's style. it plays a major role in the structure of a house, as well as its exterior aesthetic. take this tour of housetops, including explanations of specific roof types and materials, to help you choose the best roof design for your home..

Read More..

Beautifully-designed, expert-made outhouses are a sight to look at, and these east texas homemade outhouses are no exception. the finished product is an orange-brown wood box with stained glass windows, electricity, beaded paneling, and a 12 volt pc vent fan to keep the air fresh.. Choose from 50 storage shed plans that are easy to use and designed to fit any type of storage. if you can measure accurately and use essential tools, you can build your shed. to prove it to you, we’ve created a collection of the most popular shed sizes with a material list inside.. Building an outhouse may not be a woodworkers dream. however, if you need to build an outhouse you will find it easier with these plans. always read the outhouse plans carefully and make sure that there is enough information provided for you to be able to complete the project - before you invest in materials..

Build a simple utilitarian structure or create a charming and colorful outhouse to keep everyone in the family happy. add colorful painted trim and even a classic crescent moon cutout in the door for added whimsical flair. suggested materials include treated lumber, exterior plywood, exterior chipboard, reclaimed lumber, shingle siding and barn. Aug 4, 2016 - build an outhouse - 30 free outhouse plans at planspin.com. aug 4, 2016 - build an outhouse - 30 free outhouse plans at planspin.com .. saved from plans are simple and don't require fancy tools or expensive materials. saved by stephanie spencer. 136. people also love these ideas pinterest. This step by step woodworking project is about how to build a simple outhouse. i have built this simple and temporarily outhouse for my countryside property. this is super easy to build and it cost me under $150 to make. i built this project in about one week, but i only worked a few hours a day..

Read More..

Planning vs plans. since things change, plans need to get updated on a regular basis. planning is a continuous process that helps us adjust course, keep on-track and make accomplishing our goals more likely. president eisenhower said it poignantly, “in preparing for battle i have always found that plans are useless, but planning is. Strategic planning is the company’s process of defining organizational goals, missions and values (including its long-term direction) to better understand the resources and budget it needs to allocate to ensure the plan’s efficacy. this can include defining which actions need to be taken to achieve those goals from a high-level.. Work plans, whether used in professional or academic life, help you stay organized while working on projects. through work plans, you break down a process into small, achievable tasks and identify the things you want to accomplish. learn how to write a work plan so that you can be prepared for upcoming projects..

Fiu facilities management

Residence hall #1516 | university architects

Nesting chickens in buckets | chicken diy, chicken nesting

A project plan is the culmination of meticulous planning by a project manager.it is the master document that guides how a project will run, according to the manager’s intentions for each key facet of the project.. A plan without a vision is just drudgery. but a vision with a plan can change the world.” creating a plan to achieve your business objectives may not change the world—but it is possible. some of the most successful corporations started in garages, and through planning became industry giants.. A great business plan template will also provide instructions for each step of your plan and show you what an investor-ready and sba-approved business plan should look like. there are tons of free business plan templates available (including the one you can download right here on this page)..

Read More..